Type: | Alloy Steel Bar |
---|---|
Standard: | AISI, ASTM, GB, JIS, DIN, BS |
Technique: | Hot Rolled |
Application: | Structural Steel Bar, Tool Steel Bar, Die Steel Bar |
Surface Treatment: | Black/Peeling/Polishing/Machining/Grinding/Turning |
Alloy: | Alloy |
Samples: |
---|
Customization: |
---|
Suppliers with verified business licenses
Low alloy high strength steel is a kind of engineering structural steel developed by adding a small amount of Mn, Si, Nb, V, Ti, Al and other alloy elements on the basis of carbon structural steel. The so-called low alloy means that the total amount of alloy elements in steel does not exceed 3%. High strength is relative to carbon engineering structural steel. The development principle of low alloy high strength steel is to use as few alloying elements as possible to obtain as high comprehensive mechanical properties as possible, so as to meet the purpose of use and low cost. Low alloy high-strength steel can meet the requirements of large bearing capacity of various structures (such as large bridges, pressure vessels, ships, etc.) in engineering, and at the same time, it is required to reduce the dead weight of structures, improve reliability, and save materials and resources. This kind of steel is mainly used to manufacture various engineering structures with high strength requirements, such as bridges, ships, vehicles, high pressure vessels, oil and gas pipelines, large steel structures, etc. Because this kind of steel can obtain high strength without complex treatment process or even heat treatment, which greatly reduces the quality of engineering structures, it is used to replace general carbon structural steel.
Material | C | Si | Mn | P | S | Cr | Ni | Cu | Mo |
ASTM 5115 | 0.18 | 0.37 | 0.7 | 0.035 | 0.035 | 1 | 0.3 | 0.3 | 0.15 |
ASTM 5120 | 0.24 | 0.37 | 0.8 | 0.035 | 0.035 | 1 | 0.3 | 0.3 | 0.15 |
ASTM 5130 | 0.34 | 0.37 | 0.8 | 0.035 | 0.035 | 1.1 | 0.3 | 0.3 | 0.15 |
ASTM 5140 | 0.44 | 0.37 | 0.8 | 0.035 | 0.035 | 1.1 | 0.3 | 0.3 | 0.15 |
ASTM 5145 | 0.49 | 0.37 | 0.8 | 0.035 | 0.035 | 1.1 | 0.3 | 0.3 | 0.15 |
ASTM 4119 | 0.15 | 0.37 | 0.7 | 0.035 | 0.035 | 0.7 | 0.3 | 0.3 | 0.55 |
ASTM 4130 | 0.34 | 0.37 | 0.7 | 0.035 | 0.035 | 1.1 | 0.3 | 0.3 | 0.25 |
ASTM 1335 | 0.38 | 0.35 | 1.9 | 0.035 | 0.04 | 0.2 | 0.25 | 0.35 | 0.06 |
ASTM 4317 | 0.4 | 0.37 | 0.7 | 0.035 | 0.035 | 1.1 | 0.3 | 0.3 | 0.25 |
ASTM 4140 | 0.45 | 0.37 | 0.8 | 0.035 | 0.035 | 1.2 | 0.3 | 0.3 | 0.25 |
GB38CrMoAI/JIS SCM645 | 0.42 | 0.45 | 0.6 | 0.035 | 0.035 | 1.65 | 0.3 | 0.3 | 0.25 |
ASTM 6150 | 0.54 | 0.37 | 0.8 | 0.025 | 0.025 | 1.1 | 0.3 | 0.25 | 0.1 |
ASTM 4142 | 0.45 | 0.37 | 1.2 | 0.035 | 0.035 | 1.2 | 0.3 | 0.3 | 0.3 |
Production Range |
Outer Diameter:6-530mm (0.24 inch - 21.18 inch) |
Wall Thickness:0.8-200mm (0.03 inch - 7.89 inch) | |
Material / Grade |
Carbon Steel: GB/T 3094: 10#, 20#, 35#, 45#, 55#, Q235B, Q235C, CF53, A105 ASTM A519: 1010, 1020, 1026, 1035, 1045, 1050 DIN17121/EN 10297-1, DIN1629/DIN2391/EN 10305-1: C10/CK10, C22/CK22, C35/CK35, C45/CK45, CF53 JIS3441/JIS3444/JIS3445: STKM11A, STKM12A/STKM12B/STKM12C, STKM13A/STKM13B/STKM13C JIS G4051: S10C, S20C, S25C, S35C, S45C, S55C |
Alloy Steel: GB/T 3094: 16Mn(Q345B), 20Cr, 40Cr, 15CrMo, 20CrMo, 28CrMo, 30CrMo, 35CrMo, 42CrMo, 20CrMnTi, 40MnMoV, 20Mn2, ZF6, 16MnCr5, 20MnCr5, 38Mn2V, 09CrCuSb(ND) ASTM A519: 5120, 5140, 4130, 4135, 4140 DIN17121/EN 10297-1, DIN1629/DIN2391/EN 10305-1: ST52, EN10084-1998 20Cr4, 41Cr4, 15CrMo4, 25CrMo4, 35CrMo4, 42CrMo4, 16MnCr5 JIS3441/JIS3444/JIS3445: SCM432/SCRRM3, SCM4 JIS G4053: JIS SCr420, JIS SCr440, SCM415, SCM420 |
|
Tolerance | Can be customized according to customer's requirements |
Technique | Cold Drawn / Cold Rolled |
Shape | Triangle, Hexagon, Square, Rectangle, Octagon, Lemon Pipe and Others can be customized |
Further Processing for Steel Tubes | Cutting, Chamfer, Threading, Inner diameter or Outer Diameter Lathe, Surface Shot Blasting, Laser Marking |
condition
|
Heat treatment or condition
|
tensile strength
σb Mpa |
Reduction of area
ψ % |
Hot rolled bar and wire
|
Spheroidizing annealing (GKZ) or spheroidizing annealing (GKZ)+peeling (SH)
|
≤460
|
≥65
|
Pulling products
|
Cold drawing (K)+spheroidizing annealing (GKZ)
|
≤460
|
≥65
|
Pulling products
|
Cold drawing (K)+spheroidizing annealing (GKZ)+finishing (K)
|
≤490
|
≥65
|
"The tempering stability of alloy steel is better than that of carbon steel because alloy elements hinder the diffusion of atoms in the steel during tempering, thereby delaying the decomposition of martensite and resisting tempering softening at the same temperature.". Carbide forming elements have a particularly significant retarding effect on tempering softening. Although cobalt and silicon are non carbide forming elements, they have a strong retardation effect on the formation and growth of cementite nuclei, and therefore also have a delayed tempering softening effect.
30CrMo/A30302/30XM/SCM430 /4130 |
It is used to manufacture conduits with working temperature below 400 ° C, fasteners with working temperature below 450qC in boilers and steam turbines, nuts and flanges with working temperature below 500 ° C and high pressure, main shafts, shafts, gears, bolts, studs and control wheels with large load in general machinery, high-pressure conduits and weldments with working temperature below 250 ° C in chemical equipment and nitrogen and hydrogen media |
35CrMo/A30252/35XM/SCM435/4135/34CrMo4/1.7220 |
It is used to manufacture important parts in various machines that bear impact, bending and high load. Such as herringbone gear of steel rolling mill, crankshaft, hammer rod, connecting rod, fastener, main shaft and axle of steam turbine engine, engine transmission parts, large electric sleeper shaft, piercer in petroleum machinery, bolts for boiler with working temperature lower than 400 ° C, nuts with working temperature lower than 510 ° C, high-pressure seamless thick-walled pipe in chemical machinery (temperature 450-500 ° C, no corrosive medium), etc., can also replace 40CrNi for manufacturing high load transmission shaft Turbogenerator rotor, large section gear, support shaft (diameter less than 500mm), etc |
42CrMo/A30422/38XM/SCM440/4142/4140/42CrMo4/1.7225 |
It is generally used for manufacturing important parts with higher strength requirements and larger section size than 35CrMo, such as shaft, gear, connecting rod, gearbox gear, supercharger gear, engine cylinder, spring, spring clip, 1200, 2000mm oil drill pipe joint, fishing tool and replacing quenched and tempered steel with higher nickel content |
1. Who are we?
Our headquarter is located in Shandong, China. Since 2022, we have sold to North America (60.00%), Western Europe (14.00%) and South America (6.00%). There are about 11-50 people in our office.
2. How do we guarantee quality?
Always provide pre-production samples before mass production;
Always carry out final inspection before shipment;
3. What can you buy from us?
Copper, aluminum, die steel, titanium, customized machine parts
4. Why should you buy from us instead of other suppliers?
The company has 25 years of production experience. It has advanced precision production equipment, modern large warehouse, 200000 tons of inventory goods and a number of long-term stable cooperative customers.
5. What services can we provide?
Accepted delivery conditions: FOB, CFR, CIF, EXW
Accepted payment currency: US dollar, Euro, Japanese yen, Canadian dollar, Australian dollar, Hong Kong dollar, British pound, RMB, Swiss franc;
Accepted payment type: T/T, L/C, D/P D/A, PayPal;
Optional ports: Tianjin, Shanghai, Guangzhou;
Spoken: English, Chinese
6. How can we get your price?
A. We need the following information to quote for you:
1). Product Name
2). standard
3). Material grade (chemical composition)
4). dimension
5). amount
6). Special part drawing
Suppliers with verified business licenses